avionic design with actual uboot and tooling

submodule of avionic design uboot bootloader and with included tools to
get you started , read readme.md and readme-tk1-loader.md

u-boot/include/configs/socfpga_sr1500.h

@@ -0,0 +1,99 @@
+/*
+ * Copyright (C) 2015 Stefan Roese <sr@denx.de>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+#ifndef __CONFIG_SOCFPGA_SR1500_H__
+#define __CONFIG_SOCFPGA_SR1500_H__
+
+#include <asm/arch/base_addr_ac5.h>
+
+#define CONFIG_BOARD_EARLY_INIT_F
+
+#define CONFIG_SYS_NO_FLASH
+#define CONFIG_DOS_PARTITION
+#define CONFIG_FAT_WRITE
+
+#define CONFIG_HW_WATCHDOG
+
+/* Memory configurations */
+#define PHYS_SDRAM_1_SIZE		0x40000000	/* 1GiB on SR1500 */
+
+/* Booting Linux */
+#define CONFIG_BOOTFILE		"uImage"
+#define CONFIG_BOOTARGS		"console=ttyS0," __stringify(CONFIG_BAUDRATE)
+#define CONFIG_BOOTCOMMAND	"run mmcload; run mmcboot"
+#define CONFIG_LOADADDR		0x01000000
+#define CONFIG_SYS_LOAD_ADDR	CONFIG_LOADADDR
+#define CONFIG_SYS_CONSOLE_INFO_QUIET	/* don't print console @ startup */
+
+/* Ethernet on SoC (EMAC) */
+#define CONFIG_PHY_INTERFACE_MODE	PHY_INTERFACE_MODE_RGMII
+/* The PHY is autodetected, so no MII PHY address is needed here */
+#define CONFIG_PHY_MARVELL
+#define PHY_ANEG_TIMEOUT	8000
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"verify=n\0" \
+	"loadaddr=" __stringify(CONFIG_SYS_LOAD_ADDR) "\0" \
+	"ramboot=setenv bootargs " CONFIG_BOOTARGS ";" \
+		"bootm ${loadaddr} - ${fdt_addr}\0" \
+	"bootimage=zImage\0" \
+	"fdt_addr=100\0" \
+	"fdtimage=socfpga.dtb\0" \
+		"fsloadcmd=ext2load\0" \
+	"bootm ${loadaddr} - ${fdt_addr}\0" \
+	"mmcroot=/dev/mmcblk0p2\0" \
+	"mmcboot=setenv bootargs " CONFIG_BOOTARGS \
+		" root=${mmcroot} rw rootwait;" \
+		"bootz ${loadaddr} - ${fdt_addr}\0" \
+	"mmcload=mmc rescan;" \
+		"load mmc 0:1 ${loadaddr} ${bootimage};" \
+		"load mmc 0:1 ${fdt_addr} ${fdtimage}\0" \
+	"qspiload=sf probe && mtdparts default && run ubiload\0" \
+	"qspiboot=setenv bootargs " CONFIG_BOOTARGS \
+		" ubi.mtd=1,64 root=ubi0:rootfs rw rootfstype=ubifs;"\
+		"bootz ${loadaddr} - ${fdt_addr}\0" \
+	"ubiload=ubi part UBI && ubifsmount ubi0 && " \
+		"ubifsload ${loadaddr} /boot/${bootimage} && " \
+		"ubifsload ${fdt_addr} /boot/${fdtimage}\0"
+
+/* Environment */
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+
+/* Enable SPI NOR flash reset, needed for SPI booting */
+#define CONFIG_SPI_N25Q256A_RESET
+
+/*
+ * Bootcounter
+ */
+#define CONFIG_BOOTCOUNT_LIMIT
+/* last 2 lwords in OCRAM */
+#define CONFIG_SYS_BOOTCOUNT_ADDR	0xfffffff8
+#define CONFIG_SYS_BOOTCOUNT_BE
+
+/* Environment setting for SPI flash */
+#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
+#define CONFIG_ENV_SECT_SIZE	(64 * 1024)
+#define CONFIG_ENV_SIZE		(16 * 1024)
+#define CONFIG_ENV_OFFSET	0x000e0000
+#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SPI_BUS	0
+#define CONFIG_ENV_SPI_CS	0
+#define CONFIG_ENV_SPI_MODE	SPI_MODE_3
+#define CONFIG_ENV_SPI_MAX_HZ	100000000	/* Use max of 100MHz */
+#define CONFIG_SF_DEFAULT_SPEED	100000000
+
+/*
+ * The QSPI NOR flash layout on SR1500:
+ *
+ * 0000.0000 - 0003.ffff: SPL (4 times)
+ * 0004.0000 - 000d.ffff: U-Boot
+ * 000e.0000 - 000e.ffff: env1
+ * 000f.0000 - 000f.ffff: env2
+ */
+
+/* The rest of the configuration is shared */
+#include <configs/socfpga_common.h>
+
+#endif	/* __CONFIG_SOCFPGA_SR1500_H__ */