avionic design with actual uboot and tooling

submodule of avionic design uboot bootloader and with included tools to
get you started , read readme.md and readme-tk1-loader.md

u-boot/drivers/usb/host/ehci-mpc512x.c

@@ -0,0 +1,140 @@
+/*
+ * (C) Copyright 2010, Damien Dusha, <d.dusha@gmail.com>
+ *
+ * (C) Copyright 2009, Value Team S.p.A.
+ * Francesco Rendine, <francesco.rendine@valueteam.com>
+ *
+ * (C) Copyright 2009 Freescale Semiconductor, Inc.
+ *
+ * (C) Copyright 2008, Excito Elektronik i Sk=E5ne AB
+ *
+ * Author: Tor Krill tor@excito.com
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <pci.h>
+#include <usb.h>
+#include <asm/io.h>
+#include <usb/ehci-ci.h>
+
+#include "ehci.h"
+
+static void fsl_setup_phy(volatile struct ehci_hcor *);
+static void fsl_platform_set_host_mode(volatile struct usb_ehci *ehci);
+static int reset_usb_controller(volatile struct usb_ehci *ehci);
+static void usb_platform_dr_init(volatile struct usb_ehci *ehci);
+
+/*
+ * Initialize SOC FSL EHCI Controller
+ *
+ * This code is derived from EHCI FSL USB Linux driver for MPC5121
+ *
+ */
+int ehci_hcd_init(int index, enum usb_init_type init,
+		struct ehci_hccr **hccr, struct ehci_hcor **hcor)
+{
+	volatile struct usb_ehci *ehci;
+
+	/* Hook the memory mapped registers for EHCI-Controller */
+	ehci = (struct usb_ehci *)CONFIG_SYS_FSL_USB1_ADDR;
+	*hccr = (struct ehci_hccr *)((uint32_t)&(ehci->caplength));
+	*hcor = (struct ehci_hcor *)((uint32_t) *hccr +
+				HC_LENGTH(ehci_readl(&(*hccr)->cr_capbase)));
+
+	/* configure interface for UTMI_WIDE */
+	usb_platform_dr_init(ehci);
+
+	/* Init Phy USB0 to UTMI+ */
+	fsl_setup_phy(*hcor);
+
+	/* Set to host mode */
+	fsl_platform_set_host_mode(ehci);
+
+	/*
+	 * Setting the burst size seems to be required to prevent the
+	 * USB from hanging when communicating with certain USB Mass
+	 * storage devices. This was determined by analysing the
+	 * EHCI registers under Linux vs U-Boot and burstsize was the
+	 * major non-interrupt related difference between the two
+	 * implementations.
+	 *
+	 * Some USB sticks behave better than others. In particular,
+	 * the following USB stick is especially problematic:
+	 * 0930:6545 Toshiba Corp
+	 *
+	 * The burstsize is set here to match the Linux implementation.
+	 */
+	out_be32(&ehci->burstsize, FSL_EHCI_TXPBURST(8) |
+				   FSL_EHCI_RXPBURST(8));
+
+	return 0;
+}
+
+/*
+ * Destroy the appropriate control structures corresponding
+ * the the EHCI host controller.
+ */
+int ehci_hcd_stop(int index)
+{
+	volatile struct usb_ehci *ehci;
+	int exit_status = 0;
+
+	/* Reset the USB controller */
+	ehci = (struct usb_ehci *)CONFIG_SYS_FSL_USB1_ADDR;
+	exit_status = reset_usb_controller(ehci);
+
+	return exit_status;
+}
+
+static int reset_usb_controller(volatile struct usb_ehci *ehci)
+{
+	unsigned int i;
+
+	/* Command a reset of the USB Controller */
+	out_be32(&(ehci->usbcmd), CMD_RESET);
+
+	/* Wait for the reset process to finish */
+	for (i = 65535 ; i > 0 ; i--) {
+		/*
+		 * The host will set this bit to zero once the
+		 * reset process is complete
+		 */
+		if ((in_be32(&(ehci->usbcmd)) & CMD_RESET) == 0)
+			return 0;
+	}
+
+	/* Hub did not reset in time */
+	return -1;
+}
+
+static void fsl_setup_phy(volatile struct ehci_hcor *hcor)
+{
+	uint32_t portsc;
+
+	portsc  = ehci_readl(&hcor->or_portsc[0]);
+	portsc &= ~(PORT_PTS_MSK | PORT_PTS_PTW);
+
+	/* Enable the phy mode to UTMI Wide */
+	portsc |= PORT_PTS_PTW;
+	portsc |= PORT_PTS_UTMI;
+
+	ehci_writel(&hcor->or_portsc[0], portsc);
+}
+
+static void fsl_platform_set_host_mode(volatile struct usb_ehci *ehci)
+{
+	uint32_t temp;
+
+	temp  = in_le32(&ehci->usbmode);
+	temp |= CM_HOST | ES_BE;
+	out_le32(&ehci->usbmode, temp);
+}
+
+static void usb_platform_dr_init(volatile struct usb_ehci *ehci)
+{
+	/* Configure interface for UTMI_WIDE */
+	out_be32(&ehci->isiphyctrl, PHYCTRL_PHYE | PHYCTRL_PXE);
+	out_be32(&ehci->usbgenctrl, GC_PPP | GC_PFP );
+}