avionic design with actual uboot and tooling

submodule of avionic design uboot bootloader and with included tools to
get you started , read readme.md and readme-tk1-loader.md

u-boot/doc/device-tree-bindings/regulator/tps65090.txt

@@ -0,0 +1,122 @@
+TPS65090 regulators
+
+Required properties:
+- compatible: "ti,tps65090"
+- reg: I2C slave address
+- interrupts: the interrupt outputs of the controller
+- regulators: A node that houses a sub-node for each regulator within the
+  device. Each sub-node is identified using the node's name, with valid
+  values listed below. The content of each sub-node is defined by the
+  standard binding for regulators; see regulator.txt.
+  dcdc[1-3], fet[1-7] and ldo[1-2] respectively.
+- vsys[1-3]-supply: The input supply for DCDC[1-3] respectively.
+- infet[1-7]-supply: The input supply for FET[1-7] respectively.
+- vsys-l[1-2]-supply: The input supply for LDO[1-2] respectively.
+
+Optional properties:
+- ti,enable-ext-control: This is applicable for DCDC1, DCDC2 and DCDC3.
+  If DCDCs are externally controlled then this property should be there.
+- "dcdc-ext-control-gpios: This is applicable for DCDC1, DCDC2 and DCDC3.
+  If DCDCs are externally controlled and if it is from GPIO then GPIO
+  number should be provided. If it is externally controlled and no GPIO
+  entry then driver will just configure this rails as external control
+  and will not provide any enable/disable APIs.
+
+Each regulator is defined using the standard binding for regulators.
+
+Example:
+
+	tps65090@48 {
+		compatible = "ti,tps65090";
+		reg = <0x48>;
+		interrupts = <0 88 0x4>;
+
+		vsys1-supply = <&some_reg>;
+		vsys2-supply = <&some_reg>;
+		vsys3-supply = <&some_reg>;
+		infet1-supply = <&some_reg>;
+		infet2-supply = <&some_reg>;
+		infet3-supply = <&some_reg>;
+		infet4-supply = <&some_reg>;
+		infet5-supply = <&some_reg>;
+		infet6-supply = <&some_reg>;
+		infet7-supply = <&some_reg>;
+		vsys_l1-supply = <&some_reg>;
+		vsys_l2-supply = <&some_reg>;
+
+		regulators {
+			dcdc1 {
+				regulator-name = "dcdc1";
+				regulator-boot-on;
+				regulator-always-on;
+				ti,enable-ext-control;
+				dcdc-ext-control-gpios = <&gpio 10 0>;
+			};
+
+			dcdc2 {
+				regulator-name = "dcdc2";
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			dcdc3 {
+				regulator-name = "dcdc3";
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			fet1 {
+				regulator-name = "fet1";
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			fet2 {
+				regulator-name = "fet2";
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			fet3 {
+				regulator-name = "fet3";
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			fet4 {
+				regulator-name = "fet4";
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			fet5 {
+				regulator-name = "fet5";
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			fet6 {
+				regulator-name = "fet6";
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			fet7 {
+				regulator-name = "fet7";
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo1 {
+				regulator-name = "ldo1";
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo2 {
+				regulator-name = "ldo2";
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};