avionic design with actual uboot and tooling

submodule of avionic design uboot bootloader and with included tools to
get you started , read readme.md and readme-tk1-loader.md

u-boot/board/st/stv0991/Kconfig

@@ -0,0 +1,15 @@
+if TARGET_STV0991
+
+config SYS_BOARD
+	default "stv0991"
+
+config SYS_VENDOR
+	default "st"
+
+config SYS_SOC
+	default "stv0991"
+
+config SYS_CONFIG_NAME
+	default "stv0991"
+
+endif

u-boot/board/st/stv0991/MAINTAINERS

@@ -0,0 +1,6 @@
+STV0991 APPLICATION BOARD
+M:	Vikas Manocha <vikas.manocha@st.com>
+S:	Maintained
+F:	board/st/stv0991/
+F:	include/configs/stv0991.h
+F:	configs/stv0991_defconfig

u-boot/board/st/stv0991/Makefile

@@ -0,0 +1,8 @@
+#
+# (C) Copyright 2014
+# Vikas Manocha, ST Microelectronics, vikas.manocha@stcom
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y	:= stv0991.o

u-boot/board/st/stv0991/stv0991.c

@@ -0,0 +1,114 @@
+/*
+ * (C) Copyright 2014
+ * Vikas Manocha, ST Micoelectronics, vikas.manocha@st.com.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <miiphy.h>
+#include <asm/arch/stv0991_periph.h>
+#include <asm/arch/stv0991_defs.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/gpio.h>
+#include <netdev.h>
+#include <asm/io.h>
+#include <dm/platdata.h>
+#include <dm/platform_data/serial_pl01x.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+struct gpio_regs *const gpioa_regs =
+		(struct gpio_regs *) GPIOA_BASE_ADDR;
+
+#ifndef CONFIG_OF_CONTROL
+static const struct pl01x_serial_platdata serial_platdata = {
+	.base = 0x80406000,
+	.type = TYPE_PL011,
+	.clock = 2700 * 1000,
+};
+
+U_BOOT_DEVICE(stv09911_serials) = {
+	.name = "serial_pl01x",
+	.platdata = &serial_platdata,
+};
+#endif
+
+#ifdef CONFIG_SHOW_BOOT_PROGRESS
+void show_boot_progress(int progress)
+{
+	printf("%i\n", progress);
+}
+#endif
+
+void enable_eth_phy(void)
+{
+	/* Set GPIOA_06 pad HIGH (Appli board)*/
+	writel(readl(&gpioa_regs->dir) | 0x40, &gpioa_regs->dir);
+	writel(readl(&gpioa_regs->data) | 0x40, &gpioa_regs->data);
+}
+int board_eth_enable(void)
+{
+	stv0991_pinmux_config(ETH_GPIOB_10_31_C_0_4);
+	clock_setup(ETH_CLOCK_CFG);
+	enable_eth_phy();
+	return 0;
+}
+
+int board_qspi_enable(void)
+{
+	stv0991_pinmux_config(QSPI_CS_CLK_PAD);
+	clock_setup(QSPI_CLOCK_CFG);
+	return 0;
+}
+
+/*
+ * Miscellaneous platform dependent initialisations
+ */
+int board_init(void)
+{
+	board_eth_enable();
+	board_qspi_enable();
+	return 0;
+}
+
+int board_uart_init(void)
+{
+	stv0991_pinmux_config(UART_GPIOC_30_31);
+	clock_setup(UART_CLOCK_CFG);
+	return 0;
+}
+
+#ifdef CONFIG_BOARD_EARLY_INIT_F
+int board_early_init_f(void)
+{
+	board_uart_init();
+	return 0;
+}
+#endif
+
+int dram_init(void)
+{
+	gd->ram_size = PHYS_SDRAM_1_SIZE;
+	return 0;
+}
+
+void dram_init_banksize(void)
+{
+	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
+	gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
+}
+
+#ifdef CONFIG_CMD_NET
+int board_eth_init(bd_t *bis)
+{
+	int ret = 0;
+
+#if defined(CONFIG_ETH_DESIGNWARE)
+	u32 interface = PHY_INTERFACE_MODE_MII;
+	if (designware_initialize(GMAC_BASE_ADDR, interface) >= 0)
+		ret++;
+#endif
+	return ret;
+}
+#endif