avionic design with actual uboot and tooling

submodule of avionic design uboot bootloader and with included tools to
get you started , read readme.md and readme-tk1-loader.md

u-boot/board/freescale/mpc8313erdb/Kconfig

@@ -0,0 +1,12 @@
+if TARGET_MPC8313ERDB
+
+config SYS_BOARD
+	default "mpc8313erdb"
+
+config SYS_VENDOR
+	default "freescale"
+
+config SYS_CONFIG_NAME
+	default "MPC8313ERDB"
+
+endif

u-boot/board/freescale/mpc8313erdb/MAINTAINERS

@@ -0,0 +1,9 @@
+MPC8313ERDB BOARD
+#M:	-
+S:	Maintained
+F:	board/freescale/mpc8313erdb/
+F:	include/configs/MPC8313ERDB.h
+F:	configs/MPC8313ERDB_33_defconfig
+F:	configs/MPC8313ERDB_66_defconfig
+F:	configs/MPC8313ERDB_NAND_33_defconfig
+F:	configs/MPC8313ERDB_NAND_66_defconfig

u-boot/board/freescale/mpc8313erdb/Makefile

@@ -0,0 +1,8 @@
+#
+# (C) Copyright 2006
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y	:= mpc8313erdb.o sdram.o

u-boot/board/freescale/mpc8313erdb/README

@@ -0,0 +1,111 @@
+Freescale MPC8313ERDB Board
+-----------------------------------------
+
+1.	Board Switches and Jumpers
+
+	S3 is used to set CONFIG_SYS_RESET_SOURCE.
+
+	To boot the image at 0xFE000000 in NOR flash, use these DIP
+	switch settings for S3 S4:
+
+	+------+	+------+
+	|      |	| **** |
+	| **** |	|      |
+	+------+ ON	+------+ ON
+	  4321		  4321
+	(where the '*' indicates the position of the tab of the switch.)
+
+	To boot the image at the beginning of NAND flash, use these
+	DIP switch settings for S3 S4:
+
+	+------+	+------+
+	| *    |	|  *** |
+	|  *** |	| *    |
+	+------+ ON	+------+ ON
+	  4321		  4321
+	(where the '*' indicates the position of the tab of the switch.)
+
+	When booting from NAND, use u-boot-nand.bin, not u-boot.bin.
+
+2.	Memory Map
+	The memory map looks like this:
+
+	0x0000_0000	0x07ff_ffff	DDR		 128M
+	0x8000_0000	0x8fff_ffff	PCI MEM		 256M
+	0x9000_0000	0x9fff_ffff	PCI_MMIO	 256M
+	0xe000_0000	0xe00f_ffff	IMMR		 1M
+	0xe200_0000	0xe20f_ffff	PCI IO		 16M
+	0xe280_0000	0xe280_7fff	NAND FLASH (CS1) 32K
+	0xf000_0000	0xf001_ffff	VSC7385 (CS2)	 128K
+	0xfa00_0000	0xfa00_7fff	Board Status/	 32K
+					LED Control (CS3)
+	0xfe00_0000	0xfe7f_ffff	NOR FLASH (CS0)	 8M
+
+	When booting from NAND, NAND flash is CS0 and NOR flash
+	is CS1.
+
+3.	Definitions
+
+3.1	Explanation of NEW definitions in:
+
+	include/configs/MPC8313ERDB.h
+
+	CONFIG_MPC83xx		MPC83xx family
+	CONFIG_MPC831x		MPC831x specific
+	CONFIG_MPC8313ERDB	MPC8313ERDB board specific
+
+4.	Compilation
+
+	Assuming you're using BASH (or similar) as your shell:
+
+	export CROSS_COMPILE=your-cross-compiler-prefix-
+	make distclean
+	make MPC8313ERDB_XXX_config
+	(where XXX is:
+	   33 - 33 MHz oscillator, boot from NOR flash
+	   66 - 66 MHz oscillator, boot from NOR flash
+	   NAND_33 - 33 MHz oscillator, boot from NAND flash
+	   NAND_66 - 66 MHz oscillator, boot from NAND flash)
+	make
+
+5.	Downloading and Flashing Images
+
+5.1	Reflash U-Boot Image using U-Boot
+
+	NOR flash:
+
+	=>run tftpflash
+
+	You may want to try
+	=>tftpboot $loadaddr $uboot
+	first, to make sure that the TFTP load will succeed before it
+	goes ahead and wipes out your current firmware.  And of course,
+	have an alternate means of programming the flash available
+	if the new U-Boot doesn't boot.
+
+	NAND flash:
+
+	=>tftpboot $loadaddr <filename>
+	=>nand erase 0 0x80000
+	=>nand write $loadaddr 0 0x80000
+
+	...where 0x80000 is the filesize rounded up to
+	the next 0x20000 increment.
+
+5.2	Downloading and Booting Linux Kernel
+
+	Ensure that all networking-related environment variables are set
+	properly (including ipaddr, serverip, gatewayip (if needed),
+	netmask, ethaddr, eth1addr, rootpath (if using NFS root),
+	fdtfile, and bootfile).
+
+	Then, do one of the following, depending on whether you
+	want an NFS root or a ramdisk root:
+
+	=>run nfsboot
+	or
+	=>run ramboot
+
+6	Notes
+
+	The console baudrate for MPC8313ERDB is 115200bps.

u-boot/board/freescale/mpc8313erdb/mpc8313erdb.c

@@ -0,0 +1,157 @@
+/*
+ * Copyright (C) Freescale Semiconductor, Inc. 2006-2007
+ *
+ * Author: Scott Wood <scottwood@freescale.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#if defined(CONFIG_OF_LIBFDT)
+#include <libfdt.h>
+#endif
+#include <pci.h>
+#include <mpc83xx.h>
+#include <vsc7385.h>
+#include <ns16550.h>
+#include <nand.h>
+#if defined(CONFIG_MPC83XX_GPIO) && !defined(CONFIG_SPL_BUILD)
+#include <asm/gpio.h>
+#endif
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int board_early_init_f(void)
+{
+#ifndef CONFIG_SYS_8313ERDB_BROKEN_PMC
+	volatile immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
+
+	if (im->pmc.pmccr1 & PMCCR1_POWER_OFF)
+		gd->flags |= GD_FLG_SILENT;
+#endif
+#if defined(CONFIG_MPC83XX_GPIO) && !defined(CONFIG_SPL_BUILD)
+	mpc83xx_gpio_init_f();
+#endif
+
+	return 0;
+}
+
+int board_early_init_r(void)
+{
+#if defined(CONFIG_MPC83XX_GPIO) && !defined(CONFIG_SPL_BUILD)
+	mpc83xx_gpio_init_r();
+#endif
+
+	return 0;
+}
+
+int checkboard(void)
+{
+	puts("Board: Freescale MPC8313ERDB\n");
+	return 0;
+}
+
+#ifndef CONFIG_SPL_BUILD
+static struct pci_region pci_regions[] = {
+	{
+		.bus_start = CONFIG_SYS_PCI1_MEM_BASE,
+		.phys_start = CONFIG_SYS_PCI1_MEM_PHYS,
+		.size = CONFIG_SYS_PCI1_MEM_SIZE,
+		.flags = PCI_REGION_MEM | PCI_REGION_PREFETCH
+	},
+	{
+		.bus_start = CONFIG_SYS_PCI1_MMIO_BASE,
+		.phys_start = CONFIG_SYS_PCI1_MMIO_PHYS,
+		.size = CONFIG_SYS_PCI1_MMIO_SIZE,
+		.flags = PCI_REGION_MEM
+	},
+	{
+		.bus_start = CONFIG_SYS_PCI1_IO_BASE,
+		.phys_start = CONFIG_SYS_PCI1_IO_PHYS,
+		.size = CONFIG_SYS_PCI1_IO_SIZE,
+		.flags = PCI_REGION_IO
+	}
+};
+
+void pci_init_board(void)
+{
+	volatile immap_t *immr = (volatile immap_t *)CONFIG_SYS_IMMR;
+	volatile clk83xx_t *clk = (volatile clk83xx_t *)&immr->clk;
+	volatile law83xx_t *pci_law = immr->sysconf.pcilaw;
+	struct pci_region *reg[] = { pci_regions };
+
+	/* Enable all 3 PCI_CLK_OUTPUTs. */
+	clk->occr |= 0xe0000000;
+
+	/*
+	 * Configure PCI Local Access Windows
+	 */
+	pci_law[0].bar = CONFIG_SYS_PCI1_MEM_PHYS & LAWBAR_BAR;
+	pci_law[0].ar = LBLAWAR_EN | LBLAWAR_512MB;
+
+	pci_law[1].bar = CONFIG_SYS_PCI1_IO_PHYS & LAWBAR_BAR;
+	pci_law[1].ar = LBLAWAR_EN | LBLAWAR_1MB;
+
+	mpc83xx_pci_init(1, reg);
+}
+
+/*
+ * Miscellaneous late-boot configurations
+ *
+ * If a VSC7385 microcode image is present, then upload it.
+*/
+int misc_init_r(void)
+{
+	int rc = 0;
+
+#ifdef CONFIG_VSC7385_IMAGE
+	if (vsc7385_upload_firmware((void *) CONFIG_VSC7385_IMAGE,
+		CONFIG_VSC7385_IMAGE_SIZE)) {
+		puts("Failure uploading VSC7385 microcode.\n");
+		rc = 1;
+	}
+#endif
+
+	return rc;
+}
+
+#if defined(CONFIG_OF_BOARD_SETUP)
+int ft_board_setup(void *blob, bd_t *bd)
+{
+	ft_cpu_setup(blob, bd);
+#ifdef CONFIG_PCI
+	ft_pci_setup(blob, bd);
+#endif
+
+	return 0;
+}
+#endif
+#else /* CONFIG_SPL_BUILD */
+void board_init_f(ulong bootflag)
+{
+	board_early_init_f();
+	NS16550_init((NS16550_t)(CONFIG_SYS_IMMR + 0x4500),
+		     CONFIG_SYS_NS16550_CLK / 16 / CONFIG_BAUDRATE);
+	puts("NAND boot... ");
+	init_timebase();
+	initdram(0);
+	relocate_code(CONFIG_SYS_NAND_U_BOOT_RELOC_SP, (gd_t *)gd,
+		      CONFIG_SYS_NAND_U_BOOT_RELOC);
+}
+
+void board_init_r(gd_t *gd, ulong dest_addr)
+{
+	nand_boot();
+}
+
+void putc(char c)
+{
+	if (gd->flags & GD_FLG_SILENT)
+		return;
+
+	if (c == '\n')
+		NS16550_putc((NS16550_t)(CONFIG_SYS_IMMR + 0x4500), '\r');
+
+	NS16550_putc((NS16550_t)(CONFIG_SYS_IMMR + 0x4500), c);
+}
+#endif

u-boot/board/freescale/mpc8313erdb/sdram.c

@@ -0,0 +1,124 @@
+/*
+ * Copyright (C) Freescale Semiconductor, Inc. 2006-2007
+ *
+ * Authors: Nick.Spence@freescale.com
+ *          Wilson.Lo@freescale.com
+ *          scottwood@freescale.com
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <mpc83xx.h>
+#include <spd_sdram.h>
+
+#include <asm/bitops.h>
+#include <asm/io.h>
+
+#include <asm/processor.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#ifndef CONFIG_SYS_8313ERDB_BROKEN_PMC
+static void resume_from_sleep(void)
+{
+	u32 magic = *(u32 *)0;
+
+	typedef void (*func_t)(void);
+	func_t resume = *(func_t *)4;
+
+	if (magic == 0xf5153ae5)
+		resume();
+
+	gd->flags &= ~GD_FLG_SILENT;
+	puts("\nResume from sleep failed: bad magic word\n");
+}
+#endif
+
+/* Fixed sdram init -- doesn't use serial presence detect.
+ *
+ * This is useful for faster booting in configs where the RAM is unlikely
+ * to be changed, or for things like NAND booting where space is tight.
+ */
+static long fixed_sdram(void)
+{
+	u32 msize = CONFIG_SYS_DDR_SIZE * 1024 * 1024;
+
+#ifndef CONFIG_SYS_RAMBOOT
+	volatile immap_t *im = (volatile immap_t *)CONFIG_SYS_IMMR;
+	u32 msize_log2 = __ilog2(msize);
+
+	im->sysconf.ddrlaw[0].bar = CONFIG_SYS_DDR_SDRAM_BASE & 0xfffff000;
+	im->sysconf.ddrlaw[0].ar = LBLAWAR_EN | (msize_log2 - 1);
+	im->sysconf.ddrcdr = CONFIG_SYS_DDRCDR_VALUE;
+
+	/*
+	 * Erratum DDR3 requires a 50ms delay after clearing DDRCDR[DDR_cfg],
+	 * or the DDR2 controller may fail to initialize correctly.
+	 */
+	__udelay(50000);
+
+#if ((CONFIG_SYS_DDR_SDRAM_BASE & 0x00FFFFFF) != 0)
+#warning Chip select bounds is only configurable in 16MB increments
+#endif
+	im->ddr.csbnds[0].csbnds =
+		((CONFIG_SYS_DDR_SDRAM_BASE >> CSBNDS_SA_SHIFT) & CSBNDS_SA) |
+		(((CONFIG_SYS_DDR_SDRAM_BASE + msize - 1) >> CSBNDS_EA_SHIFT) &
+			CSBNDS_EA);
+	im->ddr.cs_config[0] = CONFIG_SYS_DDR_CS0_CONFIG;
+
+	/* Currently we use only one CS, so disable the other bank. */
+	im->ddr.cs_config[1] = 0;
+
+	im->ddr.sdram_clk_cntl = CONFIG_SYS_DDR_CLK_CNTL;
+	im->ddr.timing_cfg_3 = CONFIG_SYS_DDR_TIMING_3;
+	im->ddr.timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1;
+	im->ddr.timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2;
+	im->ddr.timing_cfg_0 = CONFIG_SYS_DDR_TIMING_0;
+
+#ifndef CONFIG_SYS_8313ERDB_BROKEN_PMC
+	if (im->pmc.pmccr1 & PMCCR1_POWER_OFF)
+		im->ddr.sdram_cfg = CONFIG_SYS_SDRAM_CFG | SDRAM_CFG_BI;
+	else
+#endif
+		im->ddr.sdram_cfg = CONFIG_SYS_SDRAM_CFG;
+
+	im->ddr.sdram_cfg2 = CONFIG_SYS_SDRAM_CFG2;
+	im->ddr.sdram_mode = CONFIG_SYS_DDR_MODE;
+	im->ddr.sdram_mode2 = CONFIG_SYS_DDR_MODE_2;
+
+	im->ddr.sdram_interval = CONFIG_SYS_DDR_INTERVAL;
+	sync();
+
+	/* enable DDR controller */
+	im->ddr.sdram_cfg |= SDRAM_CFG_MEM_EN;
+#endif
+
+	return msize;
+}
+
+phys_size_t initdram(int board_type)
+{
+	volatile immap_t *im = (volatile immap_t *)CONFIG_SYS_IMMR;
+	volatile fsl_lbc_t *lbc = &im->im_lbc;
+	u32 msize;
+
+	if ((im->sysconf.immrbar & IMMRBAR_BASE_ADDR) != (u32)im)
+		return -1;
+
+	/* DDR SDRAM - Main SODIMM */
+	msize = fixed_sdram();
+
+	/* Local Bus setup lbcr and mrtpr */
+	lbc->lbcr = CONFIG_SYS_LBC_LBCR;
+	lbc->mrtpr = CONFIG_SYS_LBC_MRTPR;
+	sync();
+
+#ifndef CONFIG_SYS_8313ERDB_BROKEN_PMC
+	if (im->pmc.pmccr1 & PMCCR1_POWER_OFF)
+		resume_from_sleep();
+#endif
+
+	/* return total bus SDRAM size(bytes)  -- DDR */
+	return msize;
+}