avionic design with actual uboot and tooling

submodule of avionic design uboot bootloader and with included tools to
get you started , read readme.md and readme-tk1-loader.md

u-boot/arch/mips/mach-pic32/cpu.c

@@ -0,0 +1,167 @@
+/*
+ * Copyright (C) 2015
+ * Purna Chandra Mandal <purna.mandal@microchip.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ *
+ */
+#include <common.h>
+#include <clk.h>
+#include <dm.h>
+#include <mach/pic32.h>
+#include <mach/ddr.h>
+#include <dt-bindings/clock/microchip,clock.h>
+
+/* Flash prefetch */
+#define PRECON          0x00
+
+/* Flash ECCCON */
+#define ECC_MASK	0x03
+#define ECC_SHIFT	4
+
+#define CLK_MHZ(x)	((x) / 1000000)
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static ulong rate(int id)
+{
+	int ret;
+	struct udevice *dev;
+	struct clk clk;
+	ulong rate;
+
+	ret = uclass_get_device(UCLASS_CLK, 0, &dev);
+	if (ret) {
+		printf("clk-uclass not found\n");
+		return 0;
+	}
+
+	clk.id = id;
+	ret = clk_request(dev, &clk);
+	if (ret < 0)
+		return ret;
+
+	rate = clk_get_rate(&clk);
+
+	clk_free(&clk);
+
+	return rate;
+}
+
+static ulong clk_get_cpu_rate(void)
+{
+	return rate(PB7CLK);
+}
+
+/* initialize prefetch module related to cpu_clk */
+static void prefetch_init(void)
+{
+	struct pic32_reg_atomic *regs;
+	const void __iomem *base;
+	int v, nr_waits;
+	ulong rate;
+
+	/* cpu frequency in MHZ */
+	rate = clk_get_cpu_rate() / 1000000;
+
+	/* get flash ECC type */
+	base = pic32_get_syscfg_base();
+	v = (readl(base + CFGCON) >> ECC_SHIFT) & ECC_MASK;
+
+	if (v < 2) {
+		if (rate < 66)
+			nr_waits = 0;
+		else if (rate < 133)
+			nr_waits = 1;
+		else
+			nr_waits = 2;
+	} else {
+		if (rate <= 83)
+			nr_waits = 0;
+		else if (rate <= 166)
+			nr_waits = 1;
+		else
+			nr_waits = 2;
+	}
+
+	regs = ioremap(PREFETCH_BASE + PRECON, sizeof(*regs));
+	writel(nr_waits, &regs->raw);
+
+	/* Enable prefetch for all */
+	writel(0x30, &regs->set);
+	iounmap(regs);
+}
+
+/* arch specific CPU init after DM */
+int arch_cpu_init_dm(void)
+{
+	/* flash prefetch */
+	prefetch_init();
+	return 0;
+}
+
+/* Un-gate DDR2 modules (gated by default) */
+static void ddr2_pmd_ungate(void)
+{
+	void __iomem *regs;
+
+	regs = pic32_get_syscfg_base();
+	writel(0, regs + PMD7);
+}
+
+/* initialize the DDR2 Controller and DDR2 PHY */
+phys_size_t initdram(int board_type)
+{
+	ddr2_pmd_ungate();
+	ddr2_phy_init();
+	ddr2_ctrl_init();
+	return ddr2_calculate_size();
+}
+
+int misc_init_r(void)
+{
+	set_io_port_base(0);
+	return 0;
+}
+
+#ifdef CONFIG_DISPLAY_BOARDINFO
+const char *get_core_name(void)
+{
+	u32 proc_id;
+	const char *str;
+
+	proc_id = read_c0_prid();
+	switch (proc_id) {
+	case 0x19e28:
+		str = "PIC32MZ[DA]";
+		break;
+	default:
+		str = "UNKNOWN";
+	}
+
+	return str;
+}
+#endif
+#ifdef CONFIG_CMD_CLK
+
+int soc_clk_dump(void)
+{
+	int i;
+
+	printf("PLL Speed: %lu MHz\n",
+	       CLK_MHZ(rate(PLLCLK)));
+
+	printf("CPU Speed: %lu MHz\n", CLK_MHZ(rate(PB7CLK)));
+
+	printf("MPLL Speed: %lu MHz\n", CLK_MHZ(rate(MPLL)));
+
+	for (i = PB1CLK; i <= PB7CLK; i++)
+		printf("PB%d Clock Speed: %lu MHz\n", i - PB1CLK + 1,
+		       CLK_MHZ(rate(i)));
+
+	for (i = REF1CLK; i <= REF5CLK; i++)
+		printf("REFO%d Clock Speed: %lu MHz\n", i - REF1CLK + 1,
+		       CLK_MHZ(rate(i)));
+	return 0;
+}
+#endif